What did you do to your FL5 today?

[Superhatch]

Here are a few not so helpful photos, but I'll provide more insight and proper photos in the coming weeks once I get it installed and the car tuned.

Will the tune be a before and after just with the intake?

Sponsored

 

[timestamped]

my understanding, based on following the links the grok provided to forum and discussions, was that the issue with CCV catch can is on deceleration (i.e. low-load), where the the constriction in the hose causes positive pressure which pushes oil via the turbo bearings.

is that not correct???

I use Grok as a search and summarize tool, I do not ask it to "think" or "reason" (since it usually gets it wrong) I then follow the links it provides to read for myself. it is much more efficient/faster than searching Google one forum or discussion at a time. AI is a tool that when used correctly is very helpful.

Grok has much improved in the last few months. zero hallucinations to my queries.

But note that my custom instructions to grok are about two pages long...

When I worked on genetic programming and artificial neural nets in the early/mid 1990's I called it "definitely artificial, and definitely not intelligent".

I still stand by that statement today and for the far future. AI will never think nor reason nor have emotions, though it will fake it fairly well.

what links?

 

[blueroadster]

Installed an OEM carbon fiber rear wing..

 

[zumbooruk]

what links?

sorry, did not want my original post to be too long, so I just summarized my research

here are some links with a summary of each

note that it seems that I cannot post links to the "face" site nor to the "read it" site

https://www.civicxi.com/forum/threads/the-fl5-track-junkie-thread.52760/page-82
CCV catch can spiked crankcase pressure, leading to oil ejection from turbo seals on decel with visible smoke clouds. Recommends venting or larger lines to mitigate.

TheFace /groups/typerownersofficial/posts/10165335923225744/
Type R Owners group thread on PCV vs. CCV cans for FL5. Multiple users report exhaust smoke after Radium dual kit install, attributed to over-restriction on CCV side and shop confirmed it pushes oil to turbo/exhaust.

TheFace /groups/typerownersofficial/posts/10164685263880744/
Radium CCV catch can was deemed too restrictive, causing blow-by and positive crankcase pressure that forces oil past turbo seals into exhaust.

ReadIt /r/WRX/comments/170m8qp/radium_dual_catch_can_install_a_lot_smoke_at_idle/
WRX owner (similar turbo/PCV setup) describes heavy white/blue smoke at idle post-Radium dual install. Comments point to loose fittings or improper venting creating backpressure, fixed by rechecking hoses. this is similar to the FL5 symptoms.

ReadIt /r/wrx_vb/comments/15mrrrz/ccv_vs_pcv_catchcan/
Thread on CCV vs PCV cans. Warns that a restrictive CCV routing sends oil to turbo inlet, reducing efficiency and causing exhaust smoke from bearing contamination.

ReadIt /r/wrx_vb/comments/1bhvfct/evidence_catch_cansaoss_are_needed_on_these_cars/
Detailed WRX analysis showing oil from crankcase entering turbo via restricted paths, leading to intercooler fouling and blue exhaust smoke

ReadIt /r/wrx_vb/comments/1ob7tp9/2024_wrx_burning_1l_per_3500km_dealership_will_be/
2024 WRX owner burning oil post-mods installs Radium dual cans to address. Reports initial smoke reduction but notes ongoing monitoring for CCV pressure pushing residue to exhaust.

https://www.bimmerforums.com/forum/...-oil-after-Radium-Catch-can-PCV-valve-install
BMW M54 thread (turbo-adjacent blow-by issues) details big blue smoke puffs on throttle from idle after Radium PCV can install. The cause was restricted flow leading to oil pushing past seals. It was resolved by larger hoses and check valve tweaks.

https://www.supramkv.com/threads/address-blow-by-oil-ccv-or-pcv-catch-can.33616/
Supra MKV forum on CCV/PCV cans: Blocking/restricting CCV line caused immediate exhaust smoke from oil blow-by. Users recommend non-restrictive routing to avoid turbo bearing contamination. again similar to FL5.

https://blog.edgeautosport.com/review-radium-engineering-fk8-civic-type-r-catch-cans
FK8/FL5 Radium review. Notes oil vapors slip through if pressure builds. Emphases proper install, with tips on monitoring for exhaust residue.

 

[Clark_Kent]

Will the tune be a before and after just with the intake?

The plan is to perform some before and after testing, but the measurements won't be clean. I'll do what I can and share the results.

 

[CivR]

Mustang tail lamps i mean mugen China tail lamps.

Not terrible, I do prefer stock personally. Like someone else said, it would look much better if the middle section was lit.

 

[artsyfartsyFL5]

Installed an OEM carbon fiber rear wing..

This is on my list but I got other parts calling my name, lol.

 

[AspecR]

Carismo design steering wheel review for those that were interested in the wheel.

https://www.civicxi.com/forum/threads/carismo-design-steering-wheel-you-should-get-one.61767/

 

[maxhazards]

In the spirit of OEM+. I think I’ve finally gotten around to finish installing all the creature comforts I’ve been allocating. I’m sure the taste is not for everyone and many will say well why didn’t you just get a ITS(DE5). Well this has always been my dream car to own since a young age (EK9). Fast forward modern amenities. Love everything about it.
- ITS Shift Knob
- Acuity Stage 2 shifter upgrade
- Acuity collar
- SWEDIT custom perforated Napa leather + Alcantara steering wheel upgrade (ITS Style)
- FitcamX Dash Cam
- Honda Homelink mirror
- DE5 ADS module
- Honda factory power folding mirror kit from Mikstore (model f)
- Rexpeed Mirrors (suma without branding)
- PRL P-07F wheels w/ Continental DWS06+ (275/35/R18)
- WOT Hood struts

Still to be installed:
- Project Aero front lip
- WOT/HPT Cooling plate

 

[ayospoonay]

Love the door pulls @maxhazards how are they?

 

[maxhazards]

Love the door pulls @maxhazards how are they?

Top notch quality. I believe this was the first mod I did. Bought it from the IG user turbo11thcivic. There’s a newer version (See below) of these with a full CF inlay I’d call them v2. I like the v1 instead. But to each their own. Almost 9 months later still going strong.

 

[onepointsix]

Got an Alcantara console cover from oneminibite. Quality is great!

 

[artsyfartsyFL5]

Got an Alcantara console cover from oneminibite. Quality is great!

post up some more pics if ya can! I was curious how the material was vs Overland Designs since they wrap the actual trim cover

 

[SpoolinFK8]

Some parts have started to arrive.

 

[SpoolinFK8]

In the spirit of OEM+. I think I’ve finally gotten around to finish installing all the creature comforts I’ve been allocating. I’m sure the taste is not for everyone and many will say well why didn’t you just get a ITS(DE5). Well this has always been my dream car to own since a young age (EK9). Fast forward modern amenities. Love everything about it.
- ITS Shift Knob
- Acuity Stage 2 shifter upgrade
- Acuity collar
- SWEDIT custom perforated Napa leather + Alcantara steering wheel upgrade (ITS Style)
- FitcamX Dash Cam
- Honda Homelink mirror
- DE5 ADS module
- Honda factory power folding mirror kit from Mikstore (model f)
- Rexpeed Mirrors (suma without branding)
- PRL P-07F wheels w/ Continental DWS06+ (275/35/R18)
- WOT Hood struts

Still to be installed:
- Project Aero front lip
- WOT/HPT Cooling plate

I have a few of those mods myself.