Mugen Door kick panels?

[Navy619]

Hey guys look what I found. It appears to cover the whole side It cost around $270

 

[Chilly613]

Definitely not Mugen, for sure getting ripped off for those and they more than likely are not real carbon.

Looks just like these on Amazon for less.
https://a.co/d/2GNZJMr

The only door panel protectors from Mugen.
https://www.kingmotorsports.com/p-5747-11th-gen-mugen-inner-door-protectors.aspx

 

[RODSCIVIC]

More like Fugen than Mugen

 

[Allthingsfl5]

Definitely not Mugen, for sure getting ripped off for those and they more than likely are not real carbon.

Looks just like these on Amazon for less.
https://a.co/d/2GNZJMr

The only door panel protectors from Mugen.
https://www.kingmotorsports.com/p-5747-11th-gen-mugen-inner-door-protectors.aspx

I have an order in from March that has yet to be processed. I’ve emailed them a couple times asking for an update with no response yet.

 

[Superhatch]

I have an order in from March that has yet to be processed. I’ve emailed them a couple times asking for an update with no response yet.

King?

I've always found calling Scott directly is the best option.

 

[Navy619]

More like Fugen than Mugen

 

[timestamped]

I went the cheapest route: https://a.co/d/dUIGjM6

 

[CivR]

I have an order in from March that has yet to be processed. I’ve emailed them a couple times asking for an update with no response yet.

I ordered the Mugen kick panel protector and door sill protectors and they came in within a couple weeks. Sorry you’re not having the same experience. The kick protector really saved me from a major scuff yesterday. Normally I’m pretty mindful about how I’m exiting the car, just got careless.

 

[floggindave]

I went the cheapest route: https://a.co/d/dUIGjM6

How was the install for you? I ordered from them and it seemed to be cut too small, and the loop for the speaker was cut and different thicknesses at the split.

 

[getRIGHT]

The Mugen panels are currently on back order. I can confirm

 

[Doskiller]

How was the install for you? I ordered from them and it seemed to be cut too small, and the loop for the speaker was cut and different thicknesses at the split.

When I installed my set, I found that the material used can be stretched some what. With some patience and some trial and error I was able to achieve an almost stock apperance. Super happy with mine ......... ;-) I waited about 5 months for the Mugen's with a zero ETA offered.

 

[apl360]

If that were real mugen it would’ve costed like 12k. Pretty cool tho

 

[timestamped]

How was the install for you? I ordered from them and it seemed to be cut too small, and the loop for the speaker was cut and different thicknesses at the split.

yea I started from the bottom corner of the speaker near the center of the door, and slowly worked the thin strips around the speaker, tucking the edges in with my thumbnail. There is overlap and I cut excess so that one would cover the other.

I have noticed a couple of them peeling off at an edge and reapplied some heat to stick back down. It’s not a perfect solution but it’s cheap and does the job.

 

[powerofdreams]

I went the cheapest route: https://a.co/d/dUIGjM6

I wonder if these would leave adhesive residue when removed.

 

[timestamped]

I wonder if these would leave adhesive residue when removed.

I doubt it would be anything that couldn’t be taken care of with grease/wax remover, if I take them off and try something else, I’ll post it up

Sponsored