What did you do to your FL5 today?

[BuntaTypeR]

 

[blueroadster]

Looks totally stock to me. What did you upgrade?

 

[artsyfartsyFL5]

How'd you go about disabling the ABS code? I used a resister on my 08 SI when I swapped for DC5R Recaros.

 

[BuntaTypeR]

How'd you go about disabling the ABS code? I used a resister on my 08 SI when I swapped for DC5R Recaros.

I tried using the resistor trick, but it didn’t work, so the issue is always present. I’m not too concerned about that code since I understand what’s causing it.

 

[lmtlsauto]

Received these ZE40’s Shinning Bronze GodSpecs in 19”… thank you @lmtlsauto for the fast shipping

Cant wait to see these mounted!

 

[DVH]

Installed H&R springs and an HKS Hi-Power exhaust

Would love to hear some clips of the exhaust. Stock dp and front pipe?

 

[getRIGHT]

Installed the Infinity Designs turbo inlet today. The CF weave doesn’t go exactly the same direction, but it still is not offensive to me. I think it looks great, not as good as the full Infinity Designs intake though.

Now I have to find CF radiator cooling plates that work with the Gruppe M intake or modify the ARP ones.

That looks fantastic!

I have yet to find cooling plates available for purchase for this intake yet I have seen pictures of them without any info on the maker.

I’ve been holding out trying to not to cut up the APR plates I already bought.

 

[CivR]

That looks fantastic!

I have yet to find cooling plates available for purchase for this intake yet I have seen pictures of them without any info on the maker.

I’ve been holding out trying to not to cut up the APR plates I already bought.

Thank you! The APR plates you have how is the fitment? Do you have to cut the middle and driver side piece or just the middle piece?

 

[getRIGHT]

It rate the fit as….. just ok. Of you are OCD then it will fall short

Here’s a pic of just the front mocked up and all 3 sides mocked up.
I placed some painters tape on the front piece to give a guideline to how much to cut.
I think you could get away from cutting the driver side piece but I do also have the WOT hood struts installed so I will have to notch the end pieces regardless to fit those

 

[SKINNIE]

It rate the fit as….. just ok. Of you are OCD then it will fall short

Here’s a pic of just the front mocked up and all 3 sides mocked up.
I placed some painters tape on the front piece to give a guideline to how much to cut.
I think you could get away from cutting the driver side piece but I do also have the WOT hood struts installed so I will have to notch the end pieces regardless to fit those

Is it just the GruupeM intake that requires trimming on these CF shrouds? The APR pieces are like $300 each. I sure as hell don't want to hack into them to fit lol

 

[getRIGHT]

Is it just the GruupeM intake that requires trimming on these CF shrouds? The APR pieces are like $300 each. I sure as hell don't want to hack into them to fit lol

I hear ya, which is why I haven’t brought myself to do it. I’m holding out to find a brand that’ll fit properly
The APR pieces are made to fit a stock intake box so I have seen other intakes that also need some trimming to various degrees

 

[xcstasy]

Picked it up from the dealer

 

[Andjoo]

H&R Springs have settled

 

[RODSCIVIC]

Finally got my ZE40's installed, thank @lmtlsauto center caps worked out and I'm in love with this setup. GodSpec is perfect

 

[maranelloboy05]

Finally got my ZE40's installed, thank @lmtlsauto center caps worked out and I'm in love with this setup. GodSpec is perfect

Those are 18s?